Fourier Synthesis and the Phase Problem
A diffraction pattern gives |F|, and the electron density is the Fourier transform of the structure factors — so with amplitudes and phases the structure follows by summation. The phases are not measured. This sums a real structure both ways, so you can see what the missing half was carrying.
- You supply
- One of the named structures, and how far the series should run. Everything else — the coefficients, their signs, the electron count — is computed from the atoms.
- Reading it
- Summing over h alone gives the density projected down b and c, not a section — atoms sharing an x land on top of one another. And a truncated series rings: it merges neighbours the resolution cannot separate, and can dip below zero between the atoms.
Worked examples: zirconia — 7 of 12 signs negative · aragonite, alternating signs · quartz at 6 terms — the silicons merge · quartz at 30 terms — and separate · caesium chloride — where the demonstration is empty
Input
Gaps in the row of bars are systematic absences: a centred lattice or a glide plane makes whole classes of h00 vanish, so the series has fewer terms than its length suggests and the projection repeats more often than the cell does.
The projected electron density
caesium chloride, Pm3m — 12 non-zero coefficients out of 12, carrying detail to 0.34 Å. Only one curve is visible because both sums are identical here — see below.
Summing over h alone gives the density projected down b and c onto the a axis — not a section through the cell. So a peak sits at an atom’s x whatever its y and z are, and two atoms sharing an x project on top of one another: in rock salt the sodium and the chlorine both land at 0 and at ½, and the projection cannot tell them apart. A true section along x would need every hkl.
No phase problem to show
This structure cannot show you the phase problem. Every one of its 12 coefficients is already positive, so discarding the phases changes nothing at all and the two curves are the same curve. That is not a general fact about crystals — it is what happens when the heaviest atom sits at the origin and dominates every term. Try zirconia, aragonite or quartz.
Each bar is one coefficient, drawn with its sign. A measurement gives the height of every bar and not which side of the line it is on.
What was summed
| Cell edge a | 4.1230 Å |
|---|---|
| Atoms in the cell | 2 |
| Distinct projected sites | 2 |
| F(000) | 71.99 electrons |
| Mean of the curve | 71.99 — which is F(000) again, and it never entered the series |
| Coefficients used | 12 of 12 |
| Negative coefficients | 0 |
| Highest value, phases discarded | 661.4 at x = 0 |
| Correlation of the two curves | 1.0000 |
The series stops, and a stopped series rings. Between the atoms the sum overshoots and undershoots, leaving small maxima where the crystal has nothing. Here it undershoots as far as -7.5, and a negative electron density is not a density — that is the cut-off, not the crystal. Atoms closer together in x than the series can resolve merge into one maximum: quartz’s two silicons, 0.056 apart, come out as a single peak at ½ until the series is long enough to separate them.
Where the atoms are
| x | Atoms there | Nearest maximum |
|---|---|---|
| 0.0000 | Cs | 0.0000 away |
| 0.5000 | Cl | 0.0000 away |
The distance is to the nearest maximum in the curve above, and it is an annotation rather than a test: not every atom has a peak of its own once the projection has merged it with a neighbour, and not every maximum is an atom.
Try it
zirconia — 7 of 12 signs negative · aragonite, alternating signs · quartz at 6 terms — the silicons merge · quartz at 30 terms — and separate · caesium chloride — where the demonstration is empty